Standard Courses - U.S.
All courses listed below are held at Motoman's Headquarters in Miamisburg, Ohio unless noted otherwise. To view a course description, click on a course title. You can then register for the course from the course description page or by calling us at 937-847-3307.
- DX100 Accelerated Programming
- DX100 Accelerated Programming with Arc Welding
- DX100 Advanced Arc Weld Programming
- DX100 Advanced Programming
- DX100 Basic Programming
- DX100 Basic Programming - Ivy Tech Community College - Columbus, IN
- DX100 Basic Programming PLUS Ladder Editor
- DX100 Basic Programming with Arc Welding
- DX100 Basic Programming with Coordinated Motion
- DX100 Basic Programming with Material Handling
- DX100 Com-Arc III Programming
- DX100 Coordinated Motion and Multiple Robot Control Programming
- DX100 Ladder Editor Programming
- DX100 Maintenance with Programming Overview
- DX100 Maintenance without Programming Overview
- DX100 Operator's
- DX100/FS100 MotoSight 2D Programming
- FS100 Basic Programming with Material Handling
- MLX100 Basic Programming with Material Handling
- MotoSim EG Off-Line Programming
- MotoSim EG-VRC Off-Line Programming
- MotoSim EG Off-Line Programming
- NX ComArc Web-Based / Computer-Based Training
- NX Interface Panel Web-Based / Computer-Based Training
- NX Interference Zones Web-Based Training / Computer-Based Training
- NX Ladder Editor Web-Based Training / Computer-Based Training
- NX Macro Job Web-Based Training / Computer-Based Training
- NX Shift Utilities Web-Based Training / Computer-Based Training
- NX Touch Sense Web-Based / Computer-Based Training
- NX100 Accelerated Programming
- NX100 Accelerated Programming with Arc Welding
- NX100 Advanced Arc Weld Programming
- NX100 Advanced Programming
- NX100 Basic Programming
- NX100 Basic Programming - (HACC) - HACC - Chambersburg Technology Center
- NX100 Basic Programming PLUS Ladder Editor
- NX100 Basic Programming with Arc Welding
- NX100 Basic Programming with Coordinated Motion
- NX100 Basic Programming with Material Handling
- NX100 Basic Programming with Paint
- NX100 Basic Programming with Servo Motor Spot Gun
- NX100 Com-Arc III Programming
- NX100 Coordinated Motion and Multiple Robot Control Programming
- NX100 Ladder Editor Programming
- NX100 Maintenance with Programming Overview
- NX100 Maintenance without Programming Overview
- NX100 Operator's
- NX100 Operator's Upgrade - Update skills from an Operator to a Programmer
- NX100 Operator's Upgrade w/ Arc Welding - Update skills from Operator to Programmer
- NX100 Paint Maintenance
- NX100 Paint Maintenance with Programming Overview
- XRC to NX Transition
- XRC-to-NX Transition with Arc Welding
- MotoSim EG Off-Line Programming
- NX100-to-XRC Transition
- NX100-to-XRC Transition with arc Welding
- XRC Accelerated Programming
- XRC Accelerated Programming with Arc Welding
- XRC Advanced Arc Weld Programming
- XRC Advanced Programming
- XRC Basic Programming
- XRC Basic Programming with Arc Welding
- XRC C.I/O Ladder Programming
- XRC Encoder Replacement Web Based Training /Computer Based Training
- XRC Internal Shock Sensor (ISS) Web Based Training /Computer Based Training
- XRC Macro Job - WBT / CBT Web-Based Training / Computer-Based Training
- XRC MARIO (Install & Setup) - WBT/CBT Web Based Training /Computer Based Training
- XRC Operator's
- XRC Operator's Upgrade Update skills from XRC Operator to an XRC Programmer
- XRC Operator's Upgrade w/ Arc Update skills from Operator to Programmer
- XRC SVX-, SKX-, UP-Series Maintenance with Programming Overview
- XRC SVX-, SKX-, UP-Series Maintenance without Programming Overview
